Ferrari 458 Spider Owner'S Manual Download Page 180

Page: 180 / 260

180

About your Vehicle

Super Racing seat

The seat position can be adjusted using the special controls.

Backward/forward adjustment

Pull lever

up and slide the seat forward or backward to the

desired position. Release the lever and “wiggle” in the seat to check

that it is locked in place.

Warning

The backward/forward adjustment must consider the fact

that airbag devices are placed in front of the driver and the

passenger (see page 61).
Correct adjustment must ensure there is adequate space

between the airbag and the driver/passenger (see page 61).

Seat back rake adjustment

Turn knob

clockwise or counterclockwise until the desired back

rake has been reached.

Tilting the backrest

Pull lever

up to tilt the backrest forward.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands