Ferrari 458 Spider Owner'S Manual Download Page 100

Page: 100 / 260

100

About your Vehicle

Fuel level gauge

The fuel level gauge is always displayed in area

of the display

(see page 97). The gauge has 9 yellow bars that gradually “turn off”

as the fuel level drops.

When the second bar goes off, the ﬁ rst bar turns red until fuel runs

out.

In “Fuel level low” condition, a warning light comes on on the

panel (see page 116) and a special symbol and message are

displayed for 10 seconds together with information on driving

range in km. If the condition that has generated it persists, this

signal is repeated every 8 km (5 mi).

In limited cruising range conditions, the information on driving

range in km is replaced by the words “Limited cruising range”.

Fuel level

Low

Range

86 km

Fuel level

low

Limited

cruising

range

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands