Ferrari 458 Spider Owner'S Manual Download Page 212

Page: 212 / 260

212

Advice for Emergency Situations

Disconnecting the battery

Before disconnecting the battery, deactivate the electronic alarm

using the remote control.

Warning

Never disconnect the battery from the electrical system when

the engine is running.
Before disconnecting the battery, lower the side windows by at

least 2-3 centimetres (0.8-1.2. in.) to avoid damaging the strips

when opening and closing the doors.

Warning

When the battery is connected and charged, this operation is

automatically performed when the doors are opened and closed.

The windows must remain lowered until the charged battery is

reconnected. If the battery is discharged and the windows are

fully up, only open the doors when strictly necessary and take

great care; do not close them again until the windows can be

lowered.

Important note

We recommend using the battery conditioner if the vehicle is

going to left unused for a long period.

To cut off the power supply from the battery to the electrical

system, use the quick release

on the left side of the battery. Use

the locking lever

to loosen the terminal.

attery

The battery is located in the passenger compartment behind the

passenger side footrest.

Checking the battery

Warning

The battery does not need topping up with distilled water or

sulphuric acid.

Warning

The battery must only be removed from the vehicle by the

Ferrari Service Network.

Warning

Do not place the battery near sources of heat, sparks or naked

ﬂames.

The vehicle is equipped with a sealed lead acid battery that does

not require maintenance.
• Periodically check that the terminals and pins are clean and ﬁrmly

secured.

• Visually inspect the outer casing for any cracks.
• If the battery overcharges, it will wear out quickly. Have the

vehicle electrical system checked if the battery tends to discharge

easily.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands