Ferrari 458 Spider Owner'S Manual Download Page 60

Page: 60 / 260

Safety

Pretensioners

The seat belts are ﬁ tted with pyrotechnic-powered pretensioners.

The pretensioner is activated by the airbag ECU when there is a

sufﬁ ciently severe head-on collision (impact direction between 11

and 1 o'clock p.m.) or a sufﬁ ciently severe side collision. The belt

will rewind a few centimetres just before the restraining action

begins, thereby improving the ﬁ tting across the occupant's body.
Activation of a pretensioner is signalled by the illumination of the

warning light

on the instrument panel.

Warning

Pretensioners that have been activated will no longer function

and may not be repaired under any circumstances. Contact the

Ferrari Service Network

for replacement.

When a pretensioner is activated, a small amount of smoke is

released. This smoke is not harmful.

Warning

Activation of the pretensioners only depends on the status of the

seat belts and is not affected by the occupants' presence.
If the seat belt is not fastened, the pretensioner will not activate,

even if the seat is occupied.

The seat belts are ﬁ tted with a load limiting device. The load

limiting device is located in the belt retractor and allows controlled

release of the belt during a collision thereby limiting the impact

that the belt has on the occupant's body.

Maintenance of seat belts and pretensioners

• Following a serious collision, replace the seat belts that were worn

at the time even if they do not appear to be damaged.

• Periodically check that the screws on the anchor points are tight

and that the seat belt is in perfect condition and slides smoothly.

• The seat belt must be kept clean; the presence of any dirt could

prevent the seat belt retractor from working properly.

• To clean the seat belt, wash it by hand with mild soap and water

and let it dry. Do not use strong detergents, bleach or aggressive

solvents, as they can weaken the ﬁ bres.

Make sure the retractors do not get wet: proper functioning is

only ensured if they are kept dry.

• The pretensioner requires no maintenance or lubrication.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands