Ferrari 458 Spider Owner'S Manual Download Page 198 | Manualshive

Page: 198 / 260

background image

198

Advice for Emergency Situations

Replacing other light bulbs

Roof dome light

• Use a screwdriver to gently prise under the edge of the

transparent cover

C

of the dome light

and remove it from the roof

panel.

• Replace the bulb

D

or

E

or

F

.

• Reﬁt the dome light and make sure that the wires are not trapped

by inserting it ﬁrst from the connector side and then pressing on

the opposite side.

Glove compartment, underdoor and luggage compartment bulbs

• Use a screwdriver to gently prise under the edge of the

transparent cover

G

and lift it.

• Completely remove the transparent cover from its housing.
• Take the bulb out of its clips.
• Replace the bulb.
• Reﬁt the transparent cover and make sure that the wires are not

trapped by inserting it ﬁrst from the connector side and then

pressing on the opposite side.

Follow the same procedure for replacing the underdoor light bulbs

and the luggage compartment dome light bulb.

�

�

�

�

G

«
...
196
197
198
199
200
...
»

Summary of Contents for 458 Spider





































































































































































































































































Reviews:

No comments

Related manuals for 458 Spider

Brand: Hama Pages: 2

Brand: Laser Pages: 8

Brand: Yakima Pages: 11

Brand: RACLET Pages: 48

Brand: RACLET Pages: 31

Brand: Code 3 Pages: 8

Brand: Rago FABRICATION Pages: 10

2011 A3 Sportback

Brand: Audi Pages: 29

Brand: Joie Pages: 53

Brand: Prorack Pages: 15

Brand: OHIOSTEEL Pages: 2

Brand: Xingyun Pages: 74

CMPC-22 Fujitsu-Siemens PocketLoox 410

Brand: Carcomm Pages: 2

Brand: Westin Pages: 3

Tri-Mount 34269

Brand: PowerMadd Pages: 2

Brand: Brodit Pages: 2

Brand: Whispbar Pages: 42

Brand: P-Charge Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands