Ferrari 458 Spider Owner'S Manual Download Page 53 | Manualshive

Page: 53 / 260

background image

53

3

Safety

Warning

Seat belts must be worn at all times and must be properly

fastened and adjusted!
Correct use of the seat belts can signiﬁcantly reduce the risk

and severity of injury if an accident occurs or if the vehicle

overturns.

Warning

For an effective restraining action, the seat belt must be fastened

correctly with the seat backrest in the upright position.
The seat belt is fastened correctly when the upper part of the

belt crosses the centre of the shoulder (not the neck) and the

abdominal section is ﬁtted over the hips (not the abdomen).
Make sure that the belt is not twisted and that it passes closely

over your body; if not, in the event of a head-on collision, it may

move and cause injury to the abdomen.
Avoid wearing bulky clothing that may interfere with the proper

operation of the seat belts.

Warning

Each seat belt has been designed to protect only one occupant.

If more than one person uses the same seat belt, the risk of

injury in the event of an accident is increased.
Do not sit babies, small children or other persons on your lap.
If there is a collision, the weight of an adult may cause the

child to be crushed by the seat belt causing severe or even fatal

injuries.

«
...
51
52
53
54
55
...
»

Summary of Contents for 458 Spider





































































































































































































































































Reviews:

No comments

Related manuals for 458 Spider

Brand: UnderCover Pages: 16

Brand: Kargo Master Pages: 5

Brand: Xblitz Pages: 16

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

CHASSIS CAB 3500 2017

Brand: RAM Pages: 16

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: Oldsmobile Pages: 2

Parrot MKi + ParrotCK3100 range LOGAN

Brand: Parrot Pages: 10

Brand: CTEK Pages: 84

Brand: Bestop Pages: 5

Brand: PowerMadd Pages: 3

Brand: Subaru Pages: 32

Brand: Rydeen Pages: 14

Brand: Ranger design Pages: 22

ETSS100CBKFV-BP

Brand: Soundoff Signal Pages: 2

Brand: Digi-tails Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands