Ferrari 458 Spider Owner'S Manual Download Page 196

Page: 196 / 260

196

Advice for Emergency Situations

Environment

Replace the spray can containing the expired liquid sealant. Do

not dispose of the spray can and sealant in normal domestic

waste. Dispose of in accordance with national and local

regulations or ask the

Ferrari Service Network

to take care of

disposal.

Warning

The sealant in the kit cartridge can damage the sensor inside

the wheel rim on vehicles ﬁtted with a tyre temperature and

pressure monitoring system (TPMS).
If this occurs, the sensor must be replaced

. Contact the

Ferrari

Service Network

Warning

Wear the protective gloves supplied with the tyre inﬂation and

repair kit.

Useful accessories

In addition to the tools supplied with the vehicle, the hazard

warning triangle and ﬂuorescent safety jacket should always be

kept on board in order to signal hazardous situations in compliance

with regulations.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands