Ferrari 458 Spider Owner'S Manual Download Page 221

Page: 221 / 260

221

Advice for Emergency Situations

Important note

To release the brake completely, the wrench needs to be turned

50 times, whereas it starts to be released after approximately

20 turns.

Once the electric parking brake has been manually released, the

EPB node records a failure at the next key-on and a special symbol

and the following message are displayed on the left TFT display:

“Parking Brake system revision. Go to dealer”.

Warning

The parking brake resumes normal operation, but it is important

to go to the nearest workshop to have it calibrated and delete

any errors in the error memory.

Go to a

Ferrari Service Centre.

Calibration is necessary for safety reasons.

If the electric parking brake cannot be deactivated because the

battery is ﬂat or there is a failure in the electrical system that

controls it and the vehicle needs to be moved, the emergency

release procedure described below must be performed.
• Take wrench

for EPB emergency release out of the tool bag.

Warning

Wrench

may only be used by specialised workshop

technicians, as indicated on label

on the tool bag.

• Place the release wrench

in the hole

on the rear RH gravel

guard and turn clockwise: this loosens the parking brake cables.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands