Ferrari 458 Spider Owner'S Manual Download Page 179

Page: 179 / 260

179

About your Vehicle

Tilting the backrest

To tilt the seat, pull lever

up and push the backrest towards the

front of the vehicle.
When the backrest goes back into position, it will automatically

block once it has reached the correct position.

Warning

Do not use the electric seat adjustment controls when the

backrest is tilted.

�

Seat heating system (Full Electric option)

Turn control

to activate the seat heating function.

When this function is active on one or both seats, the relative

warning light on the panel comes on. Using control

, the driver

can adjust the heating, choosing from 3 levels identiﬁed on the

control with the numbers 1, 2 and 3. In position 0, seat heating is

not activated.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands