Ferrari 458 Spider Owner'S Manual Download Page 255

Page: 255 / 260

255

Table of Contents

Safe driving ................................................................................... 150

Satellite Alarm System ................................................................ 19

Seats ......................................................................................... 39, 175

Seat adjustment ................................................................... 39, 175

Seat belts ................................................................................... 42, 56

Seat heating ................................................................................... 179

Sequential downshifting .......................................................... 147

Service .................................................................................................. 8

SETUP ............................................................................................... 96

Side airbags ..................................................................................... 68

Side airbag operating .................................................................. 68

Spare parts .......................................................................................... 7

Special recommendations ......................................................... 52

Speedometer ................................................................................. 125

Speedometer display ................................................................. 125

Speed limit setting ..................................................................... 108

SPORT 2 screen page ............................................................... 101

SPORT mode ..................................................................... 127, 155

SPORT screen page ................................................................... 101

Starting the engine .............................................................. 47, 145

Starting the vehicle ............................................................ 48, 146

Start button ................................................................................... 126

State of vehicle ............................................................................ 104

STATUS ............................................................................................. 96

Steering wheel ..................................................................... 40, 181

Stop&Start failure ....................................................................... 173

Stop&Start system (optional) ................................................ 167

Stopping the vehicle .......................................................... 49, 148

Sun visors ...................................................................................... 188

Super Racing seat ...................................................................... 180

Suspension damping control ................................................. 154

Suspension damping delink button ......................... 128, 159

Switching off the engine .................................................. 49, 148

System start-up ............................................................................ 144

Tilting the backrest .................................................................... 176

Toolkit ............................................................................................. 192

Tool bag ......................................................................................... 192

Towing ............................................................................................. 210

Tow hook ........................................................................................ 210

TPMS ................................................................................................. 76

TPMS failure ................................................................................... 81

TPMS inactive ................................................................................ 81

TPMS not calibrated ................................................................... 80

TPMS temporarily inactive ....................................................... 81

Transmission ratios ....................................................................... 27

TRIP ................................................................................................... 96

TRIP A/B ....................................................................................... 107

TRIP A and TRIP B screen pages ....................................... 107

Turn indicators ..................................................................... 45, 134

Twilight sensor ............................................................................. 134

Tyres ................................................................................................... 28

TYRES screen page .................................................................. 102

Tyre pressure .................................................................................. 28

Tyre puncture ................................................................................. 78

Tyre temperature and pressure monitoring system ....... 76

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands