Ferrari 458 Spider Owner'S Manual Download Page 19

Page: 19 / 260

General

Alarm memory

If the

CODE

symbol (see page 116) appears on the left TFT

display for 10 seconds when the vehicle is started after system

diagnosis together with the message “Break-in attempted”, this

means that an intrusion has been attempted and has activated the

alarm.
In this case, the system will indicate the reason for the alarm

activation according to the following priority:
-

LED off twice

: lifting sensor alarm

LED off three times

: door alarm

LED off four times

: luggage compartment lid alarm

LED off ﬁve times

: ignition key alarm.

The alarm system memory is reset by turning the ignition key.

Homologation

The electronic alarm system complies with EU regulations on elec-

tromagnetic compatibility and is marked in compliance.
The homologation number is referred to with the following charac-

ters.
For those markets that require the transmitter and/or receiver

marking, the homologation number is found on the component.

Satellite alarm system (optional)

On request, the vehicle can be equipped with a satellite alarm

system in some markets. If the vehicle is equipped with a satellite

alarm system, please refer to the “Nav Trak Satellite Alarm System

Quick Reference” booklet enclosed with the vehicle documents, for

further information.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands