Ferrari 458 Spider Owner'S Manual Download Page 103

Page: 103 / 260

103

About your Vehicle

Chronometer screen page

The “Chronometer” screen page is used to time laps and memorise

lap time if the vehicle is used on track. The screen page displays the

following information:

Current Lap

indicates the time elapsed since the start of the chronometer

LAP TIME / Best

indicates the time required to complete the last best lap

LAP TIME / Last

indicates the time required to complete the last lap

TOP SPEED / Best

indicates the maximum speed reached

TOP SPEED / Last

indicates the maximum speed reached in the last lap.

If the “Chronometer” screen page is being displayed and an event

occurs that needs to be displayed as a symbol and/or special

message, the screen page is minimised. For further information,

refer to the “Fault displaying logic” paragraph on page 113.

During display of the event/malfunction, the chronometer remains

active.
Each time the key is turned to on, the chronometer is reset whereas

the last valid Best Lap and Last Lap information is memorised.

Chronometer operating logic

The chronometer is controlled using the

and

DOWN

buttons that perform the following functions:
- Pressing and quickly releasing the

button:

when the chronometer is off, starts the Current Lap chronometer
when the chronometer is on, resets and restarts the Current Lap

and updates the information on previous laps (end of lap/start of

next lap)

- Pressing and quickly releasing the

DOWN

button:

when the chronometer is on, stops the chronometer and updates

information on previous laps
when the chronometer is off, displays the screen page for

adjusting display brightness

- Holding down the

DOWN

button:

when the chronometer is on or off, resets the chronometer and

information on previous laps.

Note that during display of an event/malfunction, pressing and

quickly releasing the

button interrupts the event/malfunction

display cycle (“ESCAPE” function), without affecting the

chronometer.

Current LAP

1:12:10

LAP TIME

TOP SPEED

Best:

1:11:00

Last:

1:14:40

Best:

247

Km/h

Last:

230

Km/h

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands