Ferrari 458 Spider Owner'S Manual Download Page 142

Page: 142 / 260

142

About your Vehicle

Interrupting the hard top opening/closing cycle

If button

is released before the hard top has been completely

opened or closed, it remains in a stand-by position and the message

“Complete roof cycle” appears on the left TFT display until the

opening or closing cycle is reactivated.

Warning

Do not drive until hard top opening or closing has been fully

completed.

If the hard top is still in standby position after a few minutes, an

acoustic signal will prompt you to complete the operation.

Warning

Try not to interrupt the hard top opening/closing cycle. If you

have to interrupt the opening/closing cycle, do not leave the

hard top in stand-by position for longer than 4 minutes.

Indication of hard top operating system failure

If there is a hard top operating system failure, it is indicated by

a special symbol and the message “Roof failure” on the left TFT

display.

Warning

If there is a hard top operating system failure, contact the

Ferrari Service Network

Roof failure

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands