Ferrari 458 Spider Owner'S Manual Download Page 204

Page: 204 / 260

204

Advice for Emergency Situations

Fuses and relays in passenger compartment
on passenger side

These fuses are located behind the glove compartment

Boxes

contain these fuses and relays:

Ref.

Amp.

Use

F-01

+30 Radiator fan relay 2

F-02

+30 ABS (valves)

F-03

+30 Hard top Node (pump)

F-04

+30 ABS (pump)

F-05

+30 Air conditioning Node

F-06

+30 Radiator fan relay 1

F-07

+30 Horn relay

F-08

7.5

Air conditioning and heating system compressor

F-09

7.5

+30 Supplementary stop light relay (third stop

light)

F-52

Power socket, driver seat heating

F-53

Instrument Panel Node power supply

T01

Low beam relay

T11

Heated rear window relay

T12

Service relay 1 (dependent on INT/A ignition

switch)

T13

Jumper (service power supply 2)

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands