Ferrari 458 Spider Owner'S Manual Download Page 156

Page: 156 / 260

156

About your Vehicle

RACE mode

The “RACE” mode should be used on the race track. Gearshifting

favours the racing style of the vehicle whereas the ESC system

shifts to Level 3 (engine power reductions are minimal) and the

suspension becomes even stiffer (Level 3). The performance ABS

shifts to “Sport” level. This mode is designed to ensure stability on

the race track in high grip conditions.

If “RACE” mode is selected, this is indicated on the left TFT

display as shown below:

Warning

Use of the vehicle on race tracks: after each start, cover the ﬁ rst

straight stretch of the track (at least 500 meters / 0.3 mi) at a

constant speed so that the traction control system and the ABS

may calculate exactly the grip available and the diameter of the

tyres (the calculation is reset every time the engine stops).
If this rule is not followed, system performance may be reduced.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands