Ferrari 458 Spider Owner'S Manual Download Page 90

Page: 90 / 260

About your Vehicle

Fuel ﬁller ﬂap and neck

Warning

Always turn off the engine during refuelling.
Do not smoke or use naked ﬂames when refuelling. There is a

risk of ﬁre.
The following can be harmful for your health:
- fuel coming into contact with your skin
- inhaling fuel vapours.

Opening

To open the fuel ﬁller ﬂap, press button

on the left edge of the

driver-side ﬂoor.

Closing

To close the fuel ﬁller ﬂap, push it until it clicks in place.

Emergency Opening

If the opening button does not work, the fuel ﬁller ﬂap can be

opened manually by pulling the cable

on the right-hand side of

the engine compartment.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands