Emerson unidrive sp, User Manual

Page: 69 / 420

Parameter
structure
Keypad and
display
Parameter
x.00
Parameter
description format
Advanced parameter
descriptions
Macros
Serial comms
protocol
Electronic
nameplate
Performance RFC mode
Menu 3
All modes
Unidrive SP Advanced User Guide
69
Issue Number: 10 www.controltechniques.com
*Limited to a minimum of 1 except for Ab.Servo, Fd.Servo and Fr.Servo encoders in servo mode and EnDat and SSI encoders in all modes.
Support for non power of 2 encoders was added as follows :
From software version 1.06.00 onwards - SC and SC.Endat type encoders
From software version 01.06.01 onwards - SC.Hiper, SC.SSI, Ab.servo, Fr.servo and Fd.servo type encoders.
For example - a Unidrive SP with software prior to 1.06.01 in servo mode does not store the phase offset if used with a 2000PPR quadrature encoder
When Ab, Fd, Fr, AbServo, Fd.Servo, Fr.Servo, SC, SC.Hiper, SC.EnDat or SC.SSI encoder are used the equivalent number of encoder lines per
revolution must be set-up correctly in Pr
3.34 to give the correct speed and position feedback. This is particularly important if the encoder is selected
for speed feedback with Pr 3.26 . The equivalent number of encoder lines per revolution (ELPR) is defined as follows.
For any type of linear encoder one revolution is the motor pole pitch multiplied by the number of poles set up in Pr 5.11 or Pr 21.11 .
Ab.Servo, Fd.Servo, Fr.Servo
The incremental (A/B) signal frequency should not exceed 500kHz.
It should be noted that if this parameter is set to zero the incremental signals are ignored and only the UVW commutation signals are used to define
the motor position. See Pr
3.38. If Pr 3.34 or the motor pole pairs defined by either Pr 5.11 or Pr 21.11 (depending on the motor map selected) are
modified and the encoder type is Ab.Servo, Fd.Servo or Fr.Servo then encoder is re-initialized. This ensures that the control position used by the drive
to determine the flux axis of the motor is re-aligned with the commutation signals when the encoder moves again and prevents possible errors.
SC.Hiper, SC.EnDat, SC, SC.SSI
The sine wave signal frequency can be up to 500kHz, but the resolution is reduced at higher frequencies. The table below shows the number of bits
of interpolated information at different frequencies and with different voltage levels at the drive encoder port. The total resolution in bits per revolution
is the ELPR plus the number of bits of interpolated information. Although it is possible to obtain 11 bits of interpolation information, the nominal design
value is 10 bits.
If the position feedback device is a rotary SINCOS encoder with comms the position supplied via comms gives a number of counts per revolution that
is a power of two and the resolution is defined by the single turns comms bit (Pr
3.35 ). It is assumed therefore that the number of periods per
revolution is also a power of two, and so if a SC.Hiper, SC.EnDat or SC.SSI type devices is selected and Pr 3.39 is 1 or 2 to select a rotary encoder =
1 or 2, Pr 3.34 is forced to be a power of two between 2 and 32768.
When Pr 3.34 is adjusted an Enc7 trip is produced, because the encoder requires re-initialization. If this parameter is set to a value that is not a power
of two and the encoder is set up as a linear encoder (Pr 3.39 = 0) the sample rate for the current controllers is reduced to 6kHz for 6 or 12kHz
switching frequency. All other switching frequencies are unaffected. See Pr 5.37 on page 132.
If the position feedback device is SC.Hiper or SC.EnDat it is possible for the drive to set up this parameter automatically from information obtained
from the encoder (see Pr
3.41 on page 76).
EnDat, SSI
Where encoder comms alone is used as position feedback, the equivalent lines per revolution (Pr 3.34 ) is not used in setting up the encoder interface.
If auto-configuration is used (see Pr 3.41 on page 76 for details), then Pr 3.34 is set to zero if this is successful.
Linear motors
The value entered in this parameter for a linear motor should be calculated as follows:
If this value is not an integer then an SM-Universal Encoder Plus is required.
3.34 Drive encoder lines per revolution
Drive modes Open-loop, Closed-loop vector, Servo
Coding
Bit SP FI DE Txt VM DP ND RA NC NV PT US RW BU PS
1 1 1
Range Open-loop, Closed-loop vector, Servo 0* to 50,000
Default
Open-loop, Closed-loop vector
Servo 1,024
4,096
Update rate Background read (Only has any effect when the drive is disabled)
Position feedback device ELPR
Ab, Ab.Servo number of lines per revolution
Fd, Fr, Fd.Servo, Fr.Servo number of lines per revolution / 2
SC.Hiper, SC.EnDat, SC, SC.SSI number of sine wave periods per revolution
Volt/Freq 1kHz 5kHz 50kHz 100kHz 200kHz 500kHz
1.2 11 11 10 10 9 8
1.0 11 11 10 9 9 7
0.8 10 10 10 9 8 7
0.6 10 10 9 9 8 7
0.4 9 9 9 8 7 6
NOTE
Pr 3.34 PPR setting
Motor pole pitch
Encoder pitch 4
× ( )
------------------------------------------------------ =