Emerson unidrive sp, User Manual

Page: 12 / 420

Parameter
structure
Keypad and
display
Parameter x.00
Parameter
description format
Advanced parameter
descriptions
Macros
Serial comms
protocol
Electronic
nameplate
Performance RFC mode
12
Unidrive SP Advanced User Guide
www.controltechniques.com Issue Number: 10
Holding the Up or Down key in the first method will cause the
parameters value to change more rapidly the longer the key is held, until
such time that the parameters maximum or minimum is reached.
However with the second method an increasing rate of change does not
take place when adjusting any other digit other than the least significant
digit since a digit can only have one of 10 different values. Holding the
Up or Down will cause an auto repeat and roll over to more significant
digits but the rate of change is unaltered. If the maximum or minimum is
exceeded when adjusting any other digit than the least significant one,
the maximum value will flash on the display to warn the user that the
maximum or minimum has been reached. If the user releases the Up or
Down key before the flashing stops the last in range value will re-appear
on the display. If the Up or Down key is held the display will stop flashing
after three seconds and the maximum value will be written to the
parameter. Parameters can be set to 0 by pressing the Up and Down keys
simultaneously.
2.6 SM-Keypad Plus
All SM-Keypad Plus displays built after data code N10 have software
version 4.02.00 programmed and support 5 languages (English, French,
German, Spanish and Italian) in addition to a user defined parameter set.
This software also gives the user access to two menus for SM-Keypad
Plus. Menu 40 is for SM-Keypad Plus set up, menu 41 selects commonly
used parameters for quick browsing.
Keypads built prior to N10 only support one user defined extra
parameter set only.
The SM-Keypad Plus contains two menus, menu 40 and menu 41. The
parameters in these menus are listed below.
Table 2-1 Menu 40 parameter descriptions
Table 2-2 Menu 41 parameter descriptions
For more information about the SM-Keypad Plus, see the SM-Keypad Plus User Guide .
Parameter Range(
Ú
) Default(
Ö
) Type
40.00 Parameter 0 0 to 32767 0 RW Uni
40.01 Language selection
English (0), Custom (1),
French (2), German (3),
Spanish (4), Italian (5)
English (0) RW Txt US
40.02 Software version 999999 RO Uni PT
40.03 Save to flash
Idle (0), Save (1), Restore (2),
Default (3)
Idle (0) RW Txt
40.04 LCD contrast 0 to 31 16 RW Uni US
40.05
Drive and attribute database upload was
bypassed
Updated (0), Bypass (1) RO Txt PT
40.06 Browsing favourites control Normal (0), Filter (1) Normal (0) RW Txt
40.07 Keypad security code 0 to 999 0 RW Uni US
40.08 Communication channel selection
Disable (0), Slot1 (1), Slot2 (2),
Slot3 (3), Slave (4), Direct (5)
Disable (0) RW Txt US
40.09 Hardware key code 0 to 999 0 RW Uni US
40.10 Drive node ID (Address) 0 to 255 1 RW Uni US
40.11 Flash ROM memory size 4Mbit (0), 8Mbit (1) RO Txt PT US
40.19 String database version number 0 to 999999 RO Uni PT
40.20 Screen saver strings and enable None (0), Default (1), User (2) Default (1) RW Txt US
40.21 Screen saver interval 0 to 600 120 RW Uni US
40.22 Turbo browse time interval 0 to 200ms 50ms RW Uni US
Parameter Range(
Ú
) Default(
Ö
) Type
41.00 Parameter 0 0 to 32767 0 RW Uni
41.01
to
41.50
Browsing filter source F01 to F50 Pr 0.00 to Pr 391.51 0 RW Uni
41.51 Browsing favourites control Normal (0), Filter (1) Normal (0) RW Txt
RW Read / Write RO Read only Uni Unipolar Bi Bi-polar
Bit Bit parameter Txt Text string FI Filtered DE Destination
NC Not copied RA Rating dependent PT Protected US User save
PS Power down save