dixell Ichill 260L_D DUO User Manual Download Page 107

Page: 107 / 149

1592015820 User manual IC260_261L_D DUO FW1.9 rel. 1.0

Pag. 107 of 149

Label on alarm
visualization menu

ACF1



Heat pump unit without 4-way valve not configured



Wrong configuration of defrost parameters dF22 and dF23)

ACF2



Condensing control without probe configuration.
(one probe per circuit with 2 separate circuits, at least 1 probe for common
cond.)



Fan proportional control algorithm not respected:

FA09 + FA11 + FA12 < FA10
FA12 < FA13
FA07 < FA15 < FA08



Fan proportional control algorithm not respected and pump enabled:

FA18 + FA21 + FA20 < FA19
FA21 < FA22
FA16 < FA23 < FA17



Fan ON - OFF regulation algorithm not respected:

FA09 < FA10



Fan ON - OFF regulation algorithm not respected and pump enabled:

FA18 < FA19



With pump and defrost enabled there are no evaporating/condensing
probes.



With triac regulation (CF68, CF69 = 2) the power supply configuration is
Vcc (CF83 = 0)

ACF3



Two digital / analogue inputs configured with the same function or without

the necessary resources (es. compressor 3 overload but compressor 3

relay not configured)

ACF4



CF79 = 1 and none digital input configured as Chiller request or Heat
Pump request



CF79 = 2 and none probe configured as external temperature probe



Unit configured as Heat pump and rack compressorr unit enabled (Cr01

≠0)



CF03 = 1 and wrong configuration of the digital input or digital output for
condensing unit unit

ACF5

Circuito # 2 not configured but at least one of its resources are present (relay:

solenoid pump-down, heaters, inversion valve, fan condensing ON - OFF,

recovery, auxilairy)

Summary of Contents for Ichill 260L_D DUO






















































































































































Search results

Summary of Contents for Ichill 260L_D DUO

Reviews:

Related manuals for Ichill 260L_D DUO

Brands by name

Popular brands

dixell Ichill 260L_D DUO, User Manual

Search results

Summary of Contents for Ichill 260L_D DUO

Reviews:

Related manuals for Ichill 260L_D DUO

Brands by name

Popular brands