dixell Ichill 260L_D DUO User Manual Download Page 103 | Manualshive

Page: 103 / 149

background image

1592015820 User manual IC260_261L_D DUO FW1.9 rel. 1.0

Pag. 103 of 149

ATTENTION

With air/water or water/water units and CF01=1,2 the minimum number of events per hour is 1.

AL17

Active flow input duration

Within this time the flow alarm must be active and after AL17 is expired the alarm is signalled. The counter
starts after AL15 and allows to filter the improvise flow reduction or the possible bubbles of air.

AL18

Not active flow input duration

Within this time the flow alarm must be not active and, after this time, the previous alarm is automatically
reset (if automatic) or, if manual, the unit can be restarted.

ACFL: condenser flow alarm (differential Pressure switch)

Label on alarm
visualization menu

ACFL

condenser flow alarm

Origin

Digital input active for the time set in AL55 after the water pump is on and, after
the digital input itself is activated, for the time set in AL57.
Alarm not enable if AL14=0
Alarm enabled in chiller only if AL14=1
Alarm enabled in heat pump only if AL14=2
Alarm enabled in chiller and heat pump if AL14=3

Reset

Digital input not active for the time AL58.

Restart

Automatic – Manual after AL56 (Reset procedure in Menu function).

Symbol

On the display the symbol

is blinking

Action

Alarm Relay + and buzzer on only during normal running conditions.

Loads

OFF

APFL: solar panel flow alarm

Label on alarm
visualization menu

APFL solar panel flow alarm

Origin

The flow switch alarm is not detecded for AL69 seconds starting from water
pump activation.
Flow switch alarm is signalled if the digital input is active for AL71 seconds.

Reset

Automatic reset: digital input not active for AL72 seconds.
Manual reset: Reset procedure in Menu function

Type of alarm

Automatic if flow switch digital input activation < AL70 + AL71
Manual if Automatic if flow switch digital input activation > AL70 + AL71

Symbol

On the display the symbol

is blinking

Action

Alarm Relay + and buzzer on only during normal running conditions.

Loads

Solar panel water pump OFF

AHFL: sanitary water flow alarm

Label on alarm
visualization menu

AHFL sanitary water flow alarm

Origin

The flow switch alarm is not detecded for AL65 seconds starting from water
pump activation.
Flow switch alarm is signalled if the digital input is active for AL67 seconds.

Reset

Automatic reset: digital input not active for AL68 seconds.
Manual reset: Reset procedure in Menu function

Type of alarm

Automatic if flow switch digital input activation < AL66 + AL67
Manual if Automatic if flow switch digital input activation > AL66 + AL67

Symbol

On the display the symbol

is blinking

Action

Alarm Relay + and buzzer on only during normal running conditions.

Loads

Sanitary water pump OFF

AtSF: Overload alarm of the supply fan

«
...
101
102
103
104
105
...
»

Summary of Contents for Ichill 260L_D DUO






















































































































































Reviews:

No comments

Related manuals for Ichill 260L_D DUO

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

Brand: HABONIM Pages: 9

Brand: HandyTrac Pages: 14

Brand: TA Pages: 6

Brand: MacDon Pages: 32

Brand: K&K Pages: 6

Brand: Ultratec Pages: 33

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brand: YASKAWA Pages: 66

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 17

Brand: YASKAWA Pages: 58

J1000 CIMR-JC series

Brand: YASKAWA Pages: 2

Brand: YASKAWA Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands