dixell Ichill 260L_D DUO User Manual Download Page 72 | Manualshive

Page: 72 / 149

background image

1592015820 User manual IC260_261L_D DUO FW1.9 rel. 1.0

Pag. 72 of 149

FA01

and

FA02

parameters define the operative mode of the condenser fans.

Par.

FA01

Fan regulation

0 = Output not enabled
1 = Always on
2 = ON/OFF step regulation
3 = ON/OFF continuous step regulation
4 = proportional fan speed
Par.

FA02

Condenser fan operation mode

0 = Fan on only if compressor on
1 = Independent from the compressor and off during the stand–by / or from remote OFF

Example:
Par.

FA01

=

1

/ Par.

FA02 = 0

Fans on when the compressor on (the fans work following the same output algorithm)

Par.

FA01

=

1

/ Par.

FA02 = 1

Independent from the compressor status but off in stand–by.

Par.

FA01

=

2

/ Par.

FA02

=

0

Fans on, with ON/OFF regulation and with temperature/pressure transducer control, only when the
compressor is on (at least one relay is configured as fan control). When the compressor turns off also the
fans are forced off.

Par.

FA01

=

2

/ Par.

FA02

=

1

Fans on, with ON/OFF regulation and with temperature/pressure transducer control, only when the
compressor is on (at least one relay is configured as fan control). When the compressor turns off the fans are
thermoregulated depending on the condensing temperature/pressure.

Par.

FA01

=

3

/ Par.

FA02

=

0

Fans on, with ON/OFF continuos regulation and with temperature/pressure transducer control, only when the
compressor is on (at least one relay is configured as fan control). When the compressor turns off also the
fans are forced off.

Par.

FA01

=

3

/ Par.

FA02

=

1

Fans on, with ON/OFF continuos regulation and with temperature/pressure transducer control, only when the
compressor is on (at least one relay is configured as fan control). When the compressor turns off the fans are
thermoregulated depending on the condensing temperature/pressure.

Par.

FA01

=

4

/ Par.

FA02

=

0

Fans on, with proportional regulation (PWM, 4..20mA, 0.10V) and with temperature/pressure transducer
control, only when the compressor is on. When the compressor turns off also the fans are forced off.

Par.

FA01

=

4

/ Par.

FA02

=

2

Fans on in proportional regulation (PWM, 4..20mA or 0..10V) according to condenser temperature/pressure
(only when the compressor is on).
When the compressor turns off the fans are thermoregulated depending on the condensing
temperature/pressure.

36.1 Output Step Rele’ Condenser Fan

Par FA01 = 2 ON/OFF step regulation

E.G.: 1 circuit and 4 step of ventilation

OUT relè

step n° 1

step n° 2

step n° 3

step n° 4

Out relè step n° 1

ON

OFF

OFF

OFF

Out relè step n° 2

OFF

ON

OFF

OFF

Out relè step n° 3

OFF

OFF

ON

OFF

Out relè step n° 4

OFF

OFF

OFF

ON

«
...
70
71
72
73
74
...
»

Summary of Contents for Ichill 260L_D DUO






















































































































































Reviews:

No comments

Related manuals for Ichill 260L_D DUO

ControlMaster CM15

Brand: ABB Pages: 28

Brand: Haier Pages: 58

Brand: Panasonic Pages: 16

Brand: Baby Jogger Pages: 16

Brand: Bard Pages: 8

Brand: Bardiani Valvole Pages: 35

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

Brand: Daktronics Pages: 5

Brand: Daikin Pages: 12

Brand: M-system Pages: 103

Brand: M-system Pages: 18

Brand: M-system Pages: 7

Brand: Mamas & Papas Pages: 24

Brand: Mamas & Papas Pages: 24

Brand: Parker Pages: 30

Compax3M Series

Brand: Parker Pages: 52

Brand: Parker Pages: 337

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands