manualshive.com logo in svg

dixell Ichill 260L_D DUO, User Manual

Share
Download
dixell Ichill 260L_D DUO User Manual Download Page 94

1592015820 User manual IC260_261L_D DUO FW1.9  rel. 1.0 

Pag. 94 of 149 

 after  the  DF07/2  delay  the  4-way  valve  status  is  reversed  and  normal  regulation  is 

restored. 

If chilled water is required during the production of  sanitary water, operation is the same as in the 
previous case. 
 

42.  SOLAR PANEL MANAGEMENT 

 
 
Though appropriate configuration of FS55 and FS56 parameters is possible to use the solar panel in heating 
or for sanitary hot water production. 
The solar panel is managed through the valve and water pump control; their status depend from: 

 

solar panel temperature 

 

regulation probe (typically heating regulation probe or sanitary water regulation probe); this probe is 

defined in FS57 and FS58 parameters 

 

42.1  Solar Panel In Sanitary Hot Water 

 

 

Compressors and solar panel in integration to sanitary water (FS55=1): 

If: 

solar panel temperature – sanitary temperature > FS59 (Dt to enable solar panel in sanitary water) 

the  solar  panel  are  enabled  to  work;  sanitary  probe  is  defined  by  FS57  parameter  (it  is  possible  to  set 
another probe, if needed). 
Compressors are normally managed by sanitary hot water temperature and sanitary water set point. 
 
 

 if sanitary water temperature < FS23-FS24, the valve of the solar panel is open and the water pump is on 

 if sanitary water temperature > FS23, , the valve of the solar panel is close and the water pump is off 

 

 
 

 

Solar panel in heating mode (FS55=2) 

 
If: 

solar panel temperature – sanitary temperature > FS59 (Dt to enable solar panel in sanitary water) 

the  solar  panel  are  enabled  to  work;  sanitary  probe  is  defined  by  FS57  parameter  (it  is  possible  to  set 
another probe, if needed). 
At first compressors are not used for sanitary hot water. 
It is possible to set a maximum time to use solar panel (FS61); when this time is elapsed and  sanitary set 
point is not reached, the solar panel are disabled and compressors are switched on. 
The sanitary water pump runs when solar panel are enabled. 
In regulation, if 
 

solar panel temperature – sanitary temperature < FS59 

the solar panel are disabled and the hot sanitary water is done by compressors.   
 
 
Dt control is done only at the time of the request of sanitary hot water; at this moment, if Dt< FS59 the solar 
panel are not used and compressors are used for heating. 

 
 

42.2  Solar Panel In Heating Mode 

 

 

Solar panel in integration mode (FS56=1) 

If: 

solar panel temperature – heating temperature > FS60 (Dt to enable solar panel in heating) 

Summary of Contents for Ichill 260L_D DUO






















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands