Ch12 Descriptions of Parameter Settings
| VFD-ED
12-42
Lm of Motor
Lx of Motor
Control Mode
SVC
FOCPG
Default:
0.0
Settings
0.0–6553.5 mH
Torque Compensation Low Pass Filter Time
Control Mode
SVC
Default:
0.020
Settings
0.001–10.000 sec.
Slip Compensation Low Pass Filter Time
Control Mode
SVC
Default:
0.100
Settings
0.001–10.000 sec.
Setting Pr.05-10 and Pr.05-11 changes the response time for the compensation.
When you set Pr.05-10 and Pr.05-11 to 10 seconds, it maximizes the response time for the compensation.
If the settings are too low, the system may become unstable.
Torque Compensation Gain
Control Mode
VF VFPG
Default:
0
Settings
0–10
You can set this parameter so that the AC motor drive increases its voltage output for a higher torque.
Slip Compensation Gain
Control Mode
SVC
Default:
1.00
Settings
0.00–10.00
When the motor drive controls an asynchronous motor, the load and slip increase. Use this parameter to
correct the frequency and lower the slip to make the motor run near the synchronous speed under the rated
current. When the output current is larger than the motor no-load current, the drive compensates the
frequency according to the Pr.05-13 setting. If the actual speed is slower than the expected speed,
increase the setting and vice versa.
This is only valid in SVC mode.
Slip Deviation Level
Control Mode
VFPG
SVC
FOCPG
Default:
0
Settings
0–1000%
0: Disable
Slip Deviation Detection Time
Control Mode
VFPG
SVC
FOCPG
Default:1.0
Settings
0.0–10.0 sec.
Over-slip Action
Control Mode
VFPG
SVC
FOCPG
Default:
0
Settings
0: Warn and keep operation
1: Fault and ramp to stop
2: Fault and coast to stop
Pr.05-14–Pr.05-16 set the allowable slip level and over-slip action when the drive is running.
Summary of Contents for VFD-ED Series
