Deif PPM 300 Designers Handbook Download Page 158

Page: 158 / 521

Figure 5.4

Static synchronisation principle

Synchronised

Connected genset

Synchronising genset

Time [s]

(genset

)

(busbar

) [

°]

1501 RPM
50.03 Hz

1500 RPM
50.0 Hz

Rotation (relative)

Phase synchronisation regulation

When static synchronisation starts, the frequency regulation regulates the synchronising genset frequency towards the busbar
frequency.

When the genset-busbar difference is 50 mHz, the phase synchronisation function takes over. The controller now ignores f

set point

The controlling parameter for the phase synchronisation regulation is the phase angle difference between the synchronising genset
and the busbar.

Close breaker signal

Breaker > [Breaker] > Control > [*B] Close

is activated when phase angle difference between phase L1 of the synchronising

generator and the busbar is within the

Phase window

(after the

Minimum time in phase window

timer has run out). The voltage

differences must also be within the configured range (

Delta voltage min.

and

Delta voltage max.

). This is shown in the following

drawing. In addition, the frequency differences must be within the configured range (

Delta frequency min.

and

Delta frequency

max.

The response time of the breaker is not relevant when using static synchronisation, because the slip frequency should be either very
small or zero.

DESIGNER'S HANDBOOK 4189340911K UK

Page 158 of 521

Summary of Contents for PPM 300










































































































































































































































































































































































































































































































































Search results

Summary of Contents for PPM 300

Reviews:

Related manuals for PPM 300

Brands by name

Popular brands

Deif PPM 300, Designers Handbook

Search results

Summary of Contents for PPM 300

Reviews:

Related manuals for PPM 300

Brands by name

Popular brands