manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 98

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

98

Cisco TelePresence DX70 and DX80

API Reference Guide

xCommand Audio Volume ToggleMute

Toggle the loudspeaker between muted and unmuted.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Audio Volume ToggleMute 

xCommand Audio Volume Unmute

Set the volume on the endpoint back on after muting.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Audio Volume Unmute 

xCommand Audio VuMeter Start

Start a VU meter to show the audio signal level on the specified connector. You have to specify 

both the connector's type and number (ConnectorType, ConnectorId) to uniquely identify the 

connector. The VU meter measures the input level for frequencies below 20 kHz.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Audio VuMeter Start ConnectorID: 

ConnectorID

 ConnectorType: 

ConnectorType

 [IncludePairingQuality: 

IncludePairingQuality

] 

where

ConnectorID

: Integer(1..1)

Select a connector number. Together with the ConnectorType it uniquely identifies 

the connector. Microphone [1] refers to the selected audio device (built-in loudspeak-

ers, headsets, or handset). Refer to the xStatus Audio SelectedDevice and xCommand 

Audio Select commends for more information about the selected device.

ConnectorType

: HDMI/Microphone

Select the connector type.

IncludePairingQuality

: Literal (Off / On )

The default is set to Off

xCommand Audio VuMeter Stop

Stop the VU meter on the specified connector. You have to specify both the connector's type 

and number (ConnectorType, ConnectorId) to uniquely identify the connector.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Audio VuMeter Stop ConnectorID: 

ConnectorID

 ConnectorType: 

ConnectorType

 

where

ConnectorID

: Integer(1..1)

Select a connector number. Together with the ConnectorType it uniquely identifies 

the connector. Microphone [1] refers to the selected audio device (built-in loudspeak-

ers, headsets, or handset). Refer to the xStatus Audio SelectedDevice and xCommand 

Audio Select commends for more information about the selected device.

ConnectorType

: HDMI/Microphone

Select the connector type.

xCommand Audio VuMeter StopAll

Stop all VU meters.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Audio VuMeter StopAll 

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xCommand

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands