Cisco TelePresence DX70 Reference Manual Download Page 162

Page: 162 / 202

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017.

162

Cisco TelePresence DX70 and DX80

API Reference Guide

xStatus H323 Gatekeeper Status

Shows the gatekeeper registration status.

Requires user role: ADMIN, USER

Value space of the result returned:

Required/Discovering/Discovered/Authenticating/Authenticated/Registering/Registered/

Inactive/Rejected

Example:

xStatus H323 Gatekeeper Status

*s H323 Gatekeeper Status: Registered

** end

xStatus H323 Mode Reason

Shows whether there is a conflict between H.323 settings and xStatus H323 Mode Status.
“”: When H.323 is set to On and there is no conflict between H.323 Mode configuration and

the rest of the system settings.
“SIP is enabled”: When H.323 Mode is set to On and SIP is enabled on a system that does not

support the two simultaneously.
"Not available": When a system does not support H.323.

Requires user role: ADMIN, USER

Value space of the result returned:

String

Example:

xStatus H323 Mode Reason

*s H323 Mode Reason: ""

** end

xStatus H323 Mode Status

Shows the status for H.323 registration.
Enabled: Registration is enabled.
Disabled: Registration is disable, because SIP is enabled.

Requires user role: ADMIN, USER

Value space of the result returned:

Enabled/Disabled

Example:

xStatus H323 Mode Status

*s H323 Mode Status: "Disabled"

** end

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus



xStatus

Summary of Contents for TelePresence DX70











































































































































































































Search results

Summary of Contents for TelePresence DX70

Reviews:

Brands by name

Popular brands

Cisco TelePresence DX70, Reference Manual

Search results

Summary of Contents for TelePresence DX70

Reviews:

Brands by name

Popular brands