manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 60

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

60

Cisco TelePresence DX70 and DX80

API Reference Guide

xConfiguration Network [1] Speed

Define the Ethernet link speed. We recommend not to change from the default value, which 

negotiates with the network to set the speed automatically. If you do not use autonegotia-

tion, make sure that the speed you choose is supported by the closest switch in your network 

infrastructure.

Requires user role: ADMIN, USER
Default value: Auto

USAGE:

xConfiguration Network 

n

 Speed: 

Speed

where

n

: Index that identifies the network. Range: 1..1

Speed

: Auto/10half/10full/100half/100full/1000full

Auto: Autonegotiate link speed.

10half: Force link to 10 Mbps half-duplex.
10full: Force link to 10 Mbps full-duplex.
100half: Force link to 100 Mbps half-duplex.
100full: Force link to 100 Mbps full-duplex.
1000full: Force link to 1 Gbps full-duplex.

xConfiguration Network [1] VLAN Voice Mode

Define the VLAN voice mode. The VLAN Voice Mode will be set to Auto automatically if you 

have Cisco UCM (Cisco Unified Communications Manager) as provisioning infrastructure. Note 

that Auto mode will NOT work if the NetworkServices CDP Mode setting is Off.

Requires user role: ADMIN, USER
Default value: Auto

USAGE:

xConfiguration Network 

n

 VLAN Voice Mode: 

Mode

where

n

: Index that identifies the network. Range: 1..1

Mode

: Auto/Manual/Off

Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. 

If CDP is not available, VLAN is not enabled. 
Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If 

CDP is available, the manually set value will be overruled by the value assigned by CDP.
Off: VLAN is not enabled.

xConfiguration Network [1] VLAN Voice VlanId

Define the VLAN voice ID. This setting will only take effect if Network VLAN Voice Mode is set 

to Manual.

Requires user role: ADMIN, USER
Default value: 1

USAGE:

xConfiguration Network 

n

 VLAN Voice VlanId: 

VlanId

where

n

: Index that identifies the network. Range: 1..1

VlanId

: Integer (1..4094)

Set the VLAN voice ID.

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xConfiguration

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands