manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 86

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

86

Cisco TelePresence DX70 and DX80

API Reference Guide

xConfiguration Video Input Connector [2] Quality

When encoding and transmitting video there is a trade-off between high resolution and high 

frame rate. For some video sources it is more important to transmit high frame rate than high 

resolution and vice versa. This setting specifies whether to give priority to high frame rate or to 

high resolution.

Requires user role: ADMIN, INTEGRATOR
Default value: Sharpness

USAGE:

xConfiguration Video Input Connector 

n

 Quality: 

Quality

where

n

: Unique ID that identifies the video input connector. Range: 2..2

Quality

: Motion/Sharpness

Motion: Gives the highest possible frame rate. Used when there is a need for higher 

frame rates, typically when a large number of participants are present or when there is 

a lot of motion in the picture.
Sharpness: Gives the highest possible resolution. Used when you want the highest 

quality of detailed images and graphics.

xConfiguration Video Input Connector [1..2] Visibility

Define the visibility of the video input connector in the menus on the user interface. 
Note that Connector 1 is the system's integrated camera, which is not available as a presenta-

tion source.

Requires user role: ADMIN, INTEGRATOR
Default value: Connector 1: Never   Connector 2: Always   Connector 3: OnConnect

USAGE:

xConfiguration Video Input Connector 

n

 Visibility: 

Visibility

where

n

: Unique ID that identifies the video input connector. Range: 1..2

Visibility

: Connector 1: Never   Connector 2, 3: Always/IfSignal/Never

Always: The menu selection for the video input connector will always be visible on the 

user interface.
IfSignal: Yhe menu selection for the video input connector will only be visible when 

something is connected to the video input.

Never: The input source is not expected to be used as a presentation source, and will 

not show up on the user interface.

xConfiguration Video Monitors

Define the monitor layout mode. Note that this video system supports only one monitor, so this 

value is fixed and cannot be changed.

Requires user role: ADMIN, INTEGRATOR
Default value: Single

USAGE:

xConfiguration Video Monitors: 

Monitors

where

Monitors

: Single

Single: The layout is shown on the video system's monitor.

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xConfiguration

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands