Cisco TelePresence DX70 Reference Manual Download Page 53

Page: 53 / 202

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017.

Cisco TelePresence DX70 and DX80

API Reference Guide

xConfiguration Network [1] IEEE8021X Eap Md5

Define the Md5 (Message-Digest Algorithm 5) mode. This is a Challenge Handshake

Authentication Protocol that relies on a shared secret. Md5 is a Weak security.

Requires user role: ADMIN, USER
Default value: On

USAGE:

xConfiguration Network

IEEE8021X Eap Md5:

Md5

where

: Index that identifies the network. Range: 1..1

Md5

: Off/On

Off: The EAP-MD5 protocol is disabled.
On: The EAP-MD5 protocol is enabled (default).

xConfiguration Network [1] IEEE8021X Eap Ttls

Define the TTLS (Tunneled Transport Layer Security) mode. Authenticates LAN clients without

the need for client certificates. Developed by Funk Software and Certicom. Usually supported

by Agere Systems, Proxim and Avaya.

Requires user role: ADMIN, USER
Default value: On

USAGE:

xConfiguration Network

IEEE8021X Eap Ttls:

Ttls

where

: Index that identifies the network. Range: 1..1

Ttls

: Off/On

Off: The EAP-TTLS protocol is disabled.
On: The EAP-TTLS protocol is enabled (default).

xConfiguration Network [1] IEEE8021X Eap Tls

Enable or disable the use of EAP-TLS (Transport Layer Security) for IEEE802.1x connec-

tions. The EAP-TLS protocol, defined in RFC 5216, is considered one of the most secure EAP

standards. LAN clients are authenticated using client certificates.

Requires user role: ADMIN, USER
Default value: On

USAGE:

xConfiguration Network

IEEE8021X Eap Tls:

Tls

where

: Index that identifies the network. Range: 1..1

Tls

: Off/On

Off: The EAP-TLS protocol is disabled.
On: The EAP-TLS protocol is enabled (default).

xConfiguration Network [1] IEEE8021X Eap Peap

Define the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN

clients without the need for client certificates. Developed by Microsoft, Cisco and RSA Security.

Requires user role: ADMIN, USER
Default value: On

USAGE:

xConfiguration Network

IEEE8021X Eap Peap:

Peap

where

: Index that identifies the network. Range: 1..1

Peap

: Off/On

Off: The EAP-PEAP protocol is disabled.
On: The EAP-PEAP protocol is enabled (default).

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus



xConfiguration

Summary of Contents for TelePresence DX70











































































































































































































Search results

Summary of Contents for TelePresence DX70

Reviews:

Brands by name

Popular brands

Cisco TelePresence DX70, Reference Manual

Search results

Summary of Contents for TelePresence DX70

Reviews:

Brands by name

Popular brands