manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 56

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

56

Cisco TelePresence DX70 and DX80

API Reference Guide

xConfiguration Network [1] IPv6 DHCPOptions

Retrieve a set of DHCP options, for example NTP and DNS server addresses, from a DHCPv6 

server.

Requires user role: ADMIN, USER
Default value: On

USAGE:

xConfiguration Network 

n

 IPv6 DHCPOptions: 

DHCPOptions

where

n

: Index that identifies the network. Range: 1..1

DHCPOptions

: Off/On

Off: Disable the retrieval of DHCP options from a DHCPv6 server.
On: Enable the retrieval of a selected set of DHCP options from a DHCPv6 server.

xConfiguration Network [1] MTU

Define the Ethernet MTU (Maximum Transmission Unit) size. The MTU size must be supported 

by your network infrastructure. The minimum size is 576 for IPv4 and 1280 for IPv6.

Requires user role: ADMIN, USER
Default value: 1500

USAGE:

xConfiguration Network 

n

 MTU: 

MTU

where

n

: Index that identifies the network. Range: 1..1

MTU

: Integer (576..1500)

Set a value for the MTU (bytes).

xConfiguration Network [1] QoS Mode

The QoS (Quality of Service) is a method which handles the priority of audio, video and data in 

the network. The QoS settings must be supported by the infrastructure. Diffserv (Differentiated 

Services) is a computer networking architecture that specifies a simple, scalable and coarse-

grained mechanism for classifying, managing network traffic and providing QoS priorities on 

modern IP networks.

Requires user role: ADMIN, USER
Default value: Diffserv

USAGE:

xConfiguration Network 

n

 QoS Mode: 

Mode

where

n

: Index that identifies the network. Range: 1..1

Mode

: Off/Diffserv
Off: No QoS method is used. 
Diffserv: When you set the QoS Mode to Diffserv, the Network QoS Diffserv Audio, 

Network QoS Diffserv Video, Network QoS Diffserv Data, Network QoS Diffserv 

Signalling, Network QoS Diffserv ICMPv6 and Network QoS Diffserv NTP settings are 

used to prioritize packets.

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xConfiguration

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands