Cisco TelePresence DX70 Reference Manual Download Page 201

Page: 201 / 202

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017.

201

Cisco TelePresence DX70 and DX80

API Reference Guide

User documentation for the Cisco TelePresence

products is available at



http://www.cisco.com/go/telepresence/docs

Choose a product category in the right pane until you

find the correct product. This is the path you have to

follow:

Collaboration Endpoints >

Collaboration Desk Endpoints

Alternatively, use the following short-link to find the

documentation:



http://www.cisco.com/go/dx-docs

The documents are organized in the following categories:

Install and Upgrade > Install and Upgrade Guides

•

Installation guides:

How to install the product

•

Getting started guide

: Initial configurations required to

get the system up and running

•

RCSI guide:

Regulatory compliance and safety

information

Maintain and Operate > Maintain and Operate Guides

•

Getting started guide:

Initial configurations required to

get the system up and running

•

Administrator guide:

Information required to administer

your product

Maintain and Operate > End-User Guides

•

User guides:

How to use the product

•

Quick reference guides:

How to use the product

Reference Guides | Command references

•

API reference guides:

Reference guide for the

Application Programmer Interface (API)

Reference Guides > Technical References

•

CAD drawings:

2D CAD drawings with measurements

Software Downloads, Release and General Information >

Licensing Information

•

Open source documentation:

Licenses and notices for

open source software used in this product

Software Downloads, Release and General Information >

Release Notes

•

Software release notes

User documentation on the Cisco web site

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus



Appendices

Summary of Contents for TelePresence DX70











































































































































































































Search results

Summary of Contents for TelePresence DX70

Reviews:

Brands by name

Popular brands

Cisco TelePresence DX70, Reference Manual

Search results

Summary of Contents for TelePresence DX70

Reviews:

Brands by name

Popular brands