manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 134

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

134

Cisco TelePresence DX70 and DX80

API Reference Guide

xCommand UserInterface Presentation ExternalSource State Set

Set or change the state of the input source (specified by the SourceIdentifier).

Requires user role: ADMIN, INTEGRATOR, ROOMCONTROL

USAGE:

 

xCommand UserInterface Presentation ExternalSource State Set SourceIdentifier: 

"

SourceIdentifier

" State: 

State

 [ErrorReason: "

ErrorReason

"] 

where

SourceIdentifier

: String (0, 40)

The unique string that identifies this input source. It was defined when the source was 

created with the UserInterface Presentation ExternalSource Add command.

State

: Hidden/Ready/NotReady/Error

Ready: The input source will be presented when someone selects it (taps it on the user 

interface, or when the UserInterface Presentation ExternalSource Select command is 

issued). 
NotReady: The input source is not ready, and cannot be selected. 
Error:  The input source is in an erroneous state. The ErrorReason parameter may be 

used to inform the user about the reason for failure.
Hidden: The input source will not be displayed in the user interface sharetray.

ErrorReason

: String (0, 80)

This string is displayed in the user interface sharetray, given that the State parameter is 

set to Error.

UserManagement commands

xCommand UserManagement RemoteSupportUser Create

Create a remote support user passphrase that Technical Assistance Center (TAC) can use to 

access the system for troubleshooting.

Requires user role: ADMIN

USAGE:

 

xCommand UserManagement RemoteSupportUser Create [ExpiryDays: 

ExpiryDays

] 

where

ExpiryDays

: Integer (1..31)

Define the duration for the passphrase validity. Default is 7 days.

xCommand UserManagement RemoteSupportUser Delete

Delete the remote support user created with the command xCommand UserManagement 

RemoteSupportUser Create.

Requires user role: ADMIN

USAGE:

 

xCommand UserManagement RemoteSupportUser Delete 

xCommand UserManagement RemoteSupportUser DisablePermanently

Disable the creation of new remote support users. To enable the remote support user again you 

must factory reset your system.

Requires user role: ADMIN

USAGE:

 

xCommand UserManagement RemoteSupportUser DisablePermanently Confirm: 

Confirm

 

where

Confirm

: Yes

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xCommand

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands