manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 76

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

76

Cisco TelePresence DX70 and DX80

API Reference Guide

Standby configuration

xConfiguration Standby Control

Define whether the system should go into standby mode or not.

Requires user role: ADMIN, INTEGRATOR
Default value: On

USAGE:

xConfiguration Standby Control: 

Control

where

Control

: Off/On

Off: The system will not enter standby mode.
On: The system will enter standby mode when the Standby Delay has timed out. 

Requires the Standby Delay to be set to an appropriate value.

xConfiguration Standby Delay

Define how long (in minutes) the system shall be in idle mode before it goes into standby mode. 

Requires the Standby Control to be enabled.

Requires user role: ADMIN, INTEGRATOR
Default value: 10

USAGE:

xConfiguration Standby Delay: 

Delay

where

Delay

: Integer (1..480)

Set the standby delay (minutes).

xConfiguration Standby WakeupOnMotionDetection

Automatic wake up on motion detection is a feature that will sense when a person walks into 

the room. The feature is based on ultrasound detection, and the Proximity Mode setting must 

be On to make the feature work.

Requires user role: ADMIN, INTEGRATOR
Default value: Off

USAGE:

xConfiguration Standby WakeupOnMotionDetection: 

WakeupOnMotionDetection

where

WakeupOnMotionDetection

: Off/On

Off: The wake up on motion detection is disabled. 
On: When people walk into the room the system will automatically wake up from 

standby (only applicable to DX80).

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xConfiguration

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands