manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 171

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

171

Cisco TelePresence DX70 and DX80

API Reference Guide

xStatus Network 1 IPv4 SubnetMask

Shows the subnet mask which determines which subnet an IPv4 address belongs to.

Requires user role: ADMIN, USER

Value space of the result returned: 

String

Example:

 

xStatus Network 1 IPv4 SubnetMask

*s Network 1 IPv4 SubnetMask: "255.255.255.0"

** end

xStatus Network 1 IPv6 Address

Shows the IPv6 address that uniquely identifies this system.

Requires user role: ADMIN, USER

Value space of the result returned: 

String

Example:

 

xStatus Network 1 IPv6 Address

*s Network 1 IPv6 Address: ""

** end

xStatus Network 1 IPv6 Gateway

Shows the address of the IPv6 gateway.

Requires user role: ADMIN, USER

Value space of the result returned: 

String

Example:

 

xStatus Network 1 IPv6 Gateway

*s Network 1 IPv6 Gateway: ""

** end

xStatus Network 1 VLAN Voice VlanId

The feedback shows the VLAN Voice ID; or Off if the VLAN Voice Mode is not enabled.

Requires user role: ADMIN, USER

Value space of the result returned: 

Off/1..4094

Example:

 

xStatus Network 1 VLAN Voice VlanId

*s Network 1 VLAN Voice VlanId: "Off"

** end

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xStatus

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands