manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 200

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

200

Cisco TelePresence DX70 and DX80

API Reference Guide

About disconnect cause types

The following parameters are logged when a call is 

disconnected. The disconnect cause types are used in 

disconnect events (xEvent).

CauseValue 

Proprietary. We recomend the use of CauseType and CauseCode. 

CauseType 

Describes why the call was disconnected. The value space is { OtherLocal, LocalDisconnect,  

 

 

 

UnknownRemoteSite, LocalBusy, LocalReject, InsufficientSecurity, OtherRemote, RemoteDisconnect, 

 

 

RemoteBusy, RemoteRejected, RemoteNoAnswer, CallForwarded, NetworkRejected }

CauseString 

Describes the Cause Code. 

CauseCode 

The disconnect Cause Codes are defined in SIP and Q.850.

CauseOrigin 

SIP, Q.850, internal.  

Example:

xEvent DisconnectEvent

*e CallDisconnect CauseValue: 1 

   CauseType: “LocalDisconnect” 

   CauseString: “” 

   OrigCallDirection: “outgoing” 

   RemoteURI: “[email protected]” 

   CallId: 89 

   CauseCode: 0 

   CauseOrigin: SIP

** end

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

Appendices

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands