manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 105

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

105

Cisco TelePresence DX70 and DX80

API Reference Guide

Conference commands

xCommand Conference DoNotDisturb Activate

This command switches on the Do Not Disturb mode, and the Timeout parameter allows you to 

control when it is switched off again. When Do Not Disturb is switched on, all incoming calls are 

rejected and registered as missed calls. The calling side receives a busy signal.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Conference DoNotDisturb Activate [Timeout: 

Timeout

] 

where

Timeout

: Integer (1..1440)

Set the number of minutes before Do Not Disturb is switched off. If not set, Do Not 

Disturb times out after 1440 minutes (24 hours).

xCommand Conference DoNotDisturb Deactivate

Switch off the Do Not Disturb mode. When Do Not Disturb is switched off incoming calls come 

through as normal.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Conference DoNotDisturb Deactivate 

xCommand Conference SpeakerLock Release

Releases locked speaker set by xCommand Conference SpeakerLock Set. Default voice 

switching is switched back on.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Conference SpeakerLock Release 

xCommand Conference SpeakerLock Set

For manually locking one of the speakers to the prominent speaker position. This overrides the 

default voice switching.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Conference SpeakerLock Set Target: 

Target

 [CallId: 

CallId

] 

where

Target

: local/remote

Identifies local or remote participant.

CallId

: Integer (0..65534)

Identify CallID for the remote participant. Only relevant if Target is set to "remote". The 

default is set to 0.

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xCommand

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands