manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 138

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

138

Cisco TelePresence DX70 and DX80

API Reference Guide

Video commands

xCommand Video ActiveSpeakerPIP Set

Sets position for the active speakers PiP (picture in picture).

Requires user role: ADMIN, USER

USAGE:

 

xCommand Video ActiveSpeakerPIP Set Position: 

Position

 

where

Position

: CenterLeft/CenterRight/LowerLeft/LowerRight/UpperCenter/UpperLeft/

UpperRight

Select one of the predefined positions.

xCommand Video Input SetMainVideoSource

Set which input source is the main video source. You can identify the input source by either 

the physical connector that it is connected to (ConnectorId) or the logical source identifier 

(SourceId). 

Requires user role: ADMIN, INTEGRATOR, USER

USAGE:

 

xCommand Video Input SetMainVideoSource [ConnectorId: 

ConnectorId

] [Layout: 

Layout

] [SourceId: 

SourceId

] 

where

ConnectorId

: Integer (1..5)

The identifier (ID) of the connector. Connector [n] has ID n. Run the following API 

command to find the ID: xStatus Video Input Connector.

Layout

: Literal (Equal / PIP)

Not applicable.

SourceId

: Integer (1..4)

The identifier (ID) of the input source. Input Source [n] has ID n. Run the following API 

command to find the ID: xStatus Video Input Source.

xCommand Video Layout LayoutFamily Set

Select the screen layout mode.

Requires user role: ADMIN, USER

USAGE:

 

xCommand Video Layout LayoutFamily Set [Target: 

Target

] [CallId: 

CallId

] 

LayoutFamily: 

LayoutFamily

 [CustomLayoutName: "

CustomLayoutName

"] 

where

Target

: local/remote

Select if the target is the local layout or the remote layout.

CallId

: Integer (0..65534)

The CallID is returned when the xCommand Dial command is run. During the call you 

can run the xStatus Call command to see the CallId.

LayoutFamily

: auto/custom/equal/overlay/prominent/single

Select a layout family.

CustomLayoutName

: String (1, 128)

Enter a name for the layout.

xCommand Video PresentationPIP Set

Sets position for the presentation PiP (picture in picture).

Requires user role: ADMIN, USER

USAGE:

 

xCommand Video PresentationPIP Set Position: 

Position

 

where

Position

: CenterLeft/CenterRight/LowerLeft/LowerRight/UpperCenter/UpperLeft/

UpperRight

Select one of the predefined positions.

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xCommand

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands