manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 89

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

89

Cisco TelePresence DX70 and DX80

API Reference Guide

xConfiguration Video Selfview OnCall Mode

This setting is used to switch on self-view for a short while when setting up a call. The Video 

Selfview OnCall Duration setting determines for how long it remains on. This applies when self-

view in general is switched off.

Requires user role: ADMIN, INTEGRATOR
Default value: On

USAGE:

xConfiguration Video Selfview OnCall Mode: 

Mode

where

Mode

: Off/On
Off: Self-view is not shown automatically during call setup.
On: Self-view is shown automatically during call setup.

xConfiguration Video Selfview OnCall Duration

This setting only has an effect when the Video Selfview OnCall Mode setting is switched On. In 

this case, the number of seconds set here determines for how long self-view is shown before it 

is automatically switched off.

Requires user role: ADMIN, INTEGRATOR
Default value: 10

USAGE:

xConfiguration Video Selfview OnCall Duration: 

Duration

where

Duration

: Integer (1..60)

Range: Choose for how long self-view remains on. The valid range is between 1 and 60 

seconds.

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xConfiguration

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands