manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-43

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  encapsulation dot1ad

encapsulation dot1q 
second dot1q

Double-tagged 802.1Q encapsulation. Matching criteria to be used to map 
QinQ frames ingress on an interface to the appropriate EFP. The outer tag is 
unique and the inner tag can be a single VLAN, a range of VLANs or lists 
of VLANs or VLAN ranges.

encapsulation 
untagged

Matching criteria to be used to map untagged (native) Ethernet frames 
entering an interface to the appropriate EFP.

Command

Description

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

DBM ACE9600 Operating Manual preview
ACE9600
Brand: DBM Pages: 50
A10 Thunder Series Manual preview
Thunder Series
Brand: A10 Pages: 52
Tripp Lite N125-010-GY Specification Sheet preview
N125-010-GY
Brand: Tripp Lite Pages: 2
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
T-COM Sinus 154 data II Quick Start Manual preview
Sinus 154 data II
Brand: T-COM Pages: 12
PairGain PG-Flex FLC-704 Manual preview
PG-Flex FLC-704
Brand: PairGain Pages: 20
Buffalo BS-GS2008P Quick Setup Manual preview
BS-GS2008P
Brand: Buffalo Pages: 2
Rackable Systems OmniStor 4900F Series User Manual preview
OmniStor 4900F Series
Brand: Rackable Systems Pages: 196
Ricoh Network Scanning Unit A Operating Instructions Manual preview
Network Scanning Unit A
Brand: Ricoh Pages: 206
KYLAND Technology KIEN3016A Hardware Installation Manual preview
KIEN3016A
Brand: KYLAND Technology Pages: 19
Avigilon NVR5-STD-10GBE Installation Manual preview
NVR5-STD-10GBE
Brand: Avigilon Pages: 12
ZyXEL Communications ONU5100-B22 User Manual preview
ONU5100-B22
Brand: ZyXEL Communications Pages: 2
ZyXEL Communications GS1900 Series User Manual preview
GS1900 Series
Brand: ZyXEL Communications Pages: 263
Vivotek SF8174 Quick Installation Manual preview
SF8174
Brand: Vivotek Pages: 13
ZyXEL Communications P-660R-F1 series User Manual preview
P-660R-F1 series
Brand: ZyXEL Communications Pages: 268
3Com HiPer DSP Getting Started Manual preview
HiPer DSP
Brand: 3Com Pages: 17
Caimore CM520-86WG User Manual preview
CM520-86WG
Brand: Caimore Pages: 79
Lantech TWAP-5006 User Manual preview
TWAP-5006
Brand: Lantech Pages: 20

Brands by name

Popular brands

Load more brands