Cisco 901 Command Reference Manual Download Page 190

Page: 190 / 218

1-176

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show platform tcam summary

To display the current occupancy of TCAM with summary of the number of TCAM rules allocated or
free, use the show platform tcam summary command.

show platform tcam summary

Syntax Description

This command has no arguments.

Command Modes

Privileged EXEC

Command History

Examples

The following is sample output freom the

show platform tcam summary

command:

Router#

show platform tcam summary

Ingress : 2/8 slices, 512/2048 entries used

Pre-Ingress: 3/4 slices, 768/1024 entries used

Egress : 0/4 slices, 0/512 entries used

Release

Modification

15.3(2)S

This command was introduced on the Cisco ASR 901 Series Aggregation
Services Routers.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands