Cisco 901 Command Reference Manual Download Page 207

Page: 207 / 218

1-193

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

speed

To configure the speed for a Fast Ethernet or Gigabit Ethernet interface, use the

speed

command in

interface configuration mode. To return to the default setting, use the

form of this command.

speed

{

100

1000

}

no speed

Syntax Description

Defaults

1000M

Command Modes

Interface configuration

Command History

Usage Guidelines

Use the

speed

[

100 | 1000

] command for 10/100/1000 ports and the

speed

1000

command for

Gigabit Ethernet ports.

Gigabit Ethernet Interfaces

The Gigabit Ethernet interfaces are full duplex only. You cannot change the duplex mode on the Gigabit
Ethernet interfaces or on a 10/100/1000-Mbps interface that is configured for Gigabit Ethernet.

Speed Command Syntax Combinations

Table 1-1

lists the supported command options by interface.

When manually configuring the interface speed to either 10 or 100 Mbps, the switch prompts you to
configure duplex mode on the interface.

Configures the interface to transmit at 10 Mbps.

100

Configures the interface to transmit at 100 Mbps.

1000

Configures the interface to transmit at 1000 Mbps. This keyword is valid only for
interfaces that support Gigabit Ethernet.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Table 1-13

Supported speed Command Options

Interface Type

Supported Syntax

Default Setting

Usage Guidelines

Gigabit Ethernet
module

speed

1000

Speed is 1000.

Speed, duplex, and flow control are
enabled.

10-Mbps ports

Factory set

Not applicable.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands