manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-3

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      Using Command-Line Interface

  How to Find Command Options

Router(config)# 

interface gigabitethernet ?

  <1-9>  GigabitEthernet interface number 

Router(config)# 

interface gigabitethernet 0/1

Router(config-if)#

Enter interface configuration mode by 
specifying the Gigabit Ethernet 
interface that you want to configure 
using the

 interface gigabitethernet 

global configuration command.

Enter a

 ?

 to display what you must 

enter next on the command line. In 
this example, you must enter an 
interface number from 1 to 9 in the 
format 

module-number

/

port-number

.

You are in interface configuration 
mode when the prompt changes to 

Router(config-if)#.

Router(config-if)#

?

Interface configuration commands:

  access-expression  Build a bridge boolean access expression

arp                Set arp type (arpa, probe, snap) or timeout

  backup             Modify backup parameters

  bandwidth          Set bandwidth informational parameter

  bgp-policy         Apply policy propogated by bgp community string

  bridge-group       Transparent bridging interface parameters

  carrier-delay      Specify delay for interface transitions

  cdp                CDP interface subcommands

  channel-group      Etherchannel/port bundling configuration

  clns               CLNS interface subcommands

  cmns               OSI CMNS

  custom-queue-list  Assign a custom queue list to an interface

  decnet             Interface DECnet config commands

  default            Set a command to its defaults

  delay              Specify interface throughput delay

  description        Interface specific description

  dlsw               DLSw interface subcommands

  dspu               Down Stream PU

  exit               Exit from interface configuration mode

  fair-queue         Enable Fair Queuing on an Interface

  flowcontrol        Configure flow operation.

  fras               DLC Switch Interface Command

  help               Description of the interactive help system

  hold-queue         Set hold queue depth

  ip                 Interface Internet Protocol config commands

  ipx                Novell/IPX interface subcommands

  isis               IS-IS commands

  iso-igrp           ISO-IGRP interface subcommands 

.

.

.

Router(config-if)#

Enter a

 ? 

to display a list of all the 

interface configuration commands 
available for the Gigabit Ethernet 
interface.

Table 1-2

How to Find Command Options (continued)

Command

Comment

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

D-Link DIR-862L Manual preview
DIR-862L
Brand: D-Link Pages: 4
D-Link DIR-860L Quick Install Manual preview
DIR-860L
Brand: D-Link Pages: 2
D-Link DIR-850L Resetting Manual preview
DIR-850L
Brand: D-Link Pages: 9
D-Link DIR-850L Setup And Installation Manual preview
DIR-850L
Brand: D-Link Pages: 8
D-Link DIR-865L Specifications preview
DIR-865L
Brand: D-Link Pages: 3
D-Link DIR-867 Quick Install Manual preview
DIR-867
Brand: D-Link Pages: 28
D-Link DIR-X1530 Quick Start Manual preview
DIR-X1530
Brand: D-Link Pages: 2
D-Link DSL-2540B - ADSL2/2+ Modem With EN Router Quick Install Manual preview
DSL-2540B - ADSL2/2+ Modem With EN Router
Brand: D-Link Pages: 12
D-Link DIR-882 Quick Installation Manual preview
DIR-882
Brand: D-Link Pages: 62
Watchguard XTM 5 Series Hardware Manual preview
XTM 5 Series
Brand: Watchguard Pages: 24
Tripp Lite N125-010-GY Specification Sheet preview
N125-010-GY
Brand: Tripp Lite Pages: 2
Microsoft Azure StorSimple 8100 Hardware Installation Manual preview
Azure StorSimple 8100
Brand: Microsoft Pages: 12
NETGEAR RP334 Specifications preview
RP334
Brand: NETGEAR Pages: 2
ProCurve J8454A Quick Start Manual preview
J8454A
Brand: ProCurve Pages: 2
NKE BOX Wi-Fi User Manual And Installation Manual preview
BOX Wi-Fi
Brand: NKE Pages: 15
Conel UR5i v2 SL User Manual preview
UR5i v2 SL
Brand: Conel Pages: 32
3Com EtherLink 3C905C-TX User Manual preview
EtherLink 3C905C-TX
Brand: 3Com Pages: 96
Intercoax IXWB-450 Quick Start Manual preview
IXWB-450
Brand: Intercoax Pages: 2

Brands by name

Popular brands

Load more brands