Cisco 901 Command Reference Manual Download Page 94

Page: 94 / 218

1-80

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

network-clock wait-to-restore

Specifies the amount of time in seconds that the Cisco ASR 901 waits before considering a new clock
source. Specify the

network-clock wait-to-restore-timeout

command in the interface configuration

mode.

network-clock wait-to-restore

<0-86400>

no network-clock wait-to-restore

<0-86400>

Syntax Description

Defaults

The default setting is

network-clock-select wait-to-restore 300

Command Modes

Interface configuration mode.

Command History

Usage Guidelines

The wait to restore time is configurable in the range of 0 to 86400 seconds. The default value is 300
seconds.

Caution

Ensure that you set the wait-to-restore values above 50 seconds to avoid a timing flap.

Examples

The following example shows how to use the

network-clock wait-to-restore

command:

Router#

config t

Router(config-if)#

network-clock wait-to-restore 1000

global

Router(config-if)#

exit

Related Commands

<0-86400>

The wait to restore time is configurable in the range of 0 to 86400 seconds.
The default value is 300 seconds.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Command

Description

set network-clocks
force-reselect

Forces the router to re-select the network clock.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands