Cisco 901 Command Reference Manual Download Page 203

Page: 203 / 218

1-189

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show xconnect

To display information about xconnect attachment circuits and pseudowires (PWs), use the

show

xconnect all

command in privileged EXEC mode.

show xconnect

{

all

interface

interface

peer

ip-address

{

all

vcid

vcid

}} [

detail

]

Syntax Description

Command Modes

Privileged EXEC

Command History

Usage Guidelines

The

show xconnect all

command can be used to display, sort, and filter basic information about all

xconnect attachment circuits and PWs.

all

Displays information about all xconnect attachment circuits and PWs.

interface

interface

Displays information about xconnect attachment circuits and PWs on the specified
interface. Valid values for the argument are as follows:

•

atm

numbe

r—Displays xconnect information for a specific ATM interface or

subinterface.

•

atm

number

vpi-value

—Displays virtual path (VP) xconnect information

for a specific ATM virtual path identifier (VPI). This command does not
display information about virtual connect (VC) xconnects using the specified
VPI.

•

atm

number

vpi-value/vci-value

—Displays VC xconnect information for a

specific ATM VPI and virtual circuit identifier (VCI) combination.

•

serial

number

—Displays xconnect information for a specific serial interface.

•

serial

number dlci-number

—Displays xconnect information for a specific

Frame Relay data-link connection identifier (DLCI).

•

vlan

vlan-number

—Displays vlan-mode xconnect information for a specific

VLAN interface.

peer

ip-address

{

all

vcid

vcid

}

Displays information about xconnect attachment circuits and PWs associated with
the specified peer IP address.

•

all

—Displays all xconnect information associated with the specified peer IP

address.

•

vcid

vcid

—Displays xconnect information associated with the specified peer IP

address and the specified VC ID.

detail

(Optional) Displays detailed information about the specified xconnect attachment
circuits and PWs.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands