manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-140

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  set precedence

service-policy

Attaches a policy map to an input interface or VC, or an output interface 
or VC, to be used as the service policy for that interface or VC.

set cos

Sets the Layer 2 CoS value of an outgoing packet.

set dscp

Marks a packet by setting the Layer 3 DSCP value in the ToS byte.

set qos-group

Sets a group ID that can be used later to classify packets.

show policy-map

Displays the configuration of all classes for a specified service policy map 
or all classes for all existing policy maps.

show policy-map 
interface

Displays the configuration for all classes configured for all service 
policies on the specified interface or displays the classes for the service 
policy for a specific PVC on the interface.

show table-map

Displays the configuration of a specified table map or all table maps.

table-map (value 
mapping)

Creates and configures a mapping table for mapping and converting one 
packet-marking value to another.

Command

Description

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Profile LS901-E1 Instruction Manual preview
LS901-E1
Brand: Profile Pages: 6
H3C S10500 Series Mpls Configuration Manual preview
S10500 Series
Brand: H3C Pages: 400
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Brand: AMX Pages: 1
MSNswitch UIS-322b Quick Installation Manual preview
UIS-322b
Brand: MSNswitch Pages: 2
Rosco ND100 User Manual preview
ND100
Brand: Rosco Pages: 20
l-com HA72170-NF Installation Manual preview
HA72170-NF
Brand: l-com Pages: 2
Alvarion BreezeNET DS.11 Configuration Utility Release Note preview
BreezeNET DS.11 Configuration Utility
Brand: Alvarion Pages: 2
Beck com.tom INDUSTRY 100.WLAN.W Startup Manual preview
com.tom INDUSTRY 100.WLAN.W
Brand: Beck Pages: 2
Allynk Technology CAG-0100 User Manual preview
CAG-0100
Brand: Allynk Technology Pages: 39
PairGain T1L2F10A Manual preview
T1L2F10A
Brand: PairGain Pages: 76
ATCOM AXE2DL + EC64L User Manual preview
AXE2DL + EC64L
Brand: ATCOM Pages: 18
Xaptum ENF XAP-RW-001 Quick Start Manual preview
ENF XAP-RW-001
Brand: Xaptum Pages: 24
Magnescale MG80-EI Operating Manual preview
MG80-EI
Brand: Magnescale Pages: 73
Zte MF28B User Manual preview
MF28B
Brand: Zte Pages: 32
Edimax AR-7084A Quick Installation Manual preview
AR-7084A
Brand: Edimax Pages: 8
Edimax IC-5150W Quick Installation Manual preview
IC-5150W
Brand: Edimax Pages: 19
SingTel AC1900 Quick Installation Manual preview
AC1900
Brand: SingTel Pages: 2
Rutenbeck Line21 Installation Instructions preview
Line21
Brand: Rutenbeck Pages: 4

Brands by name

Popular brands

Load more brands