Cisco 901 Command Reference Manual Download Page 21

Page: 21 / 218

1-7

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

asr901-ecmp-hash-config ipv4-type

To specify equal-cost multi-path routing (ECMP) hashing algorithm for IPv4 configuration, use the

asr901-ecmp-hash-config ipv4-type

command in global configuration mode. To remove this

configuration, use the

form of this command.

asr901-ecmp-hash-config ipv4-type

{

dest-addrs

dest-l4-port

l3-proto-id

outer-vlan

src-addrs

src-intf

src-l4-port

}

add

no asr901-ecmp-hash-config ipv4-type

{

dest-addrs

dest-l4-port

l3-proto-id

outer-vlan

src-addrs

src-intf

src-l4-port

}

add

Syntax Description

Command Default

The ECMP parameters, such as

dest-l4-port

src-intf

, and

src-l4-port

are disabled by default.

Command Modes

Global configuration (config)#

Command History

Usage Guidelines

This command is used to configure IPv4 type ECMP hash configurations for improved load distribution
of IP traffic. All the ECMP parameters are enabled by default except

dest-l4-port

src-intf

, and

src-l4-port

. You should configure the

asr901-ecmp-hash-config ipv4-type

command

to enable them.

Examples

The following example shows how to configure IPv4 type ECMP hash configuration on a
Cisco ASR 901 router:

Router#

configure terminal

Router(config)#

asr901-ecmp-hash-config ipv4-type dest-addrs

Router(config)#

asr901-ecmp-hash-config ipv4-type dest-addrs add

dest-addrs

Specifies the destination IPv4 address.

dest-l4-port

Specifies the destination Layer 4 port.

l3-proto-id

Specifies the Layer 3 protocol identifier.

outer-vlan

Specifies the outer virtual local area network (VLAN).

src-addrs

Specifies the source IPv4 address.

src-intf

Specifies the source or the incoming interface.

src-l4-port

Specifies the source Layer 4 port.

add

Adds IPv4 ECMP hash configuration.

Release

Modification

15.3(2)S

This command was introduced on the Cisco ASR 901 Series Aggregation
Services Routers.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands