Cisco 901 Command Reference Manual Download Page 194 | Manualshive

Page: 194 / 218

background image

1-180

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show policy-map interface

Command Default

This command displays the packet statistics of all classes that are configured for all service policies on
the specified interface or subinterface or on a specific permanent virtual circuit (PVC) on the interface.

The absence of both the forward slash (

/

) and a

vpi

value defaults the

vpi

value to 0. If this value is

omitted, information for all virtual circuits (VCs) on the specified ATM interface or subinterface is
displayed.

Command Modes

Privileged EXEC (#)

Command History

Usage Guidelines

The

show policy-map interface

command displays the packet statistics for classes on the specified

interface or the specified PVC only if a service policy has been attached to the interface or the PVC.

The counters displayed after the

show policy-map interface

command is entered are updated only if

congestion is present on the interface.

/

subslot

(ATM shared port adapter only) Secondary slot number on an SPA interface
processor (SIP) where a SPA is installed. See the platform-specific SPA
hardware installation guide and the corresponding “Specifying the Interface
Address on an SPA” topic in the platform-specific SPA software
configuration guide for subslot information.

/

port

(ATM shared port adapter only) Port or interface number. See the
appropriate hardware manual for port information. For SPAs, see the
corresponding “Specifying the Interface Address” topics in the
platform-specific SPA software configuration guide

.

.

subinterface

(ATM shared port adapter only—Optional) Subinterface number. The
number that precedes the period must match the number to which this
subinterface belongs. The range is 1 to 4,294,967,293.

interface-type

(Optional) Interface type; possible valid values are

ethernet

,

gigabitethernet

,

tengigabitethernet

interface-number

(Optional) Module and port number; see the “Usage Guidelines” section for
valid values.

null 0

(Optional) Specifies the null interface; the only valid value is 0.

vlan

vlan-id

(Optional) Specifies the VLAN ID; valid values are from 1 to 4094.

detailed

(Optional) Displays additional statistics.

class

class-name

(Optional) Displays the QoS policy actions for the specified class.

port-channel

channel-number

(Optional) Displays the EtherChannel port-channel interface.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

«
...
192
193
194
195
196
...
»

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Brand: Icidu Pages: 10

Brand: YATO Pages: 96

Brand: ActionTec Pages: 115

ELITENAS EN104L+(B)

Brand: Sans Digital Pages: 9

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

IPLink 2603 Series

Brand: Patton Pages: 120

Brand: Alcatel-Lucent Pages: 12

Brand: Planet Pages: 2

Brand: Multi-Link Pages: 31

Brand: MicroNova Pages: 113

Brand: Avigilon Pages: 12

Brand: Cabletron Systems Pages: 56

Brand: Airaya Pages: 28

Network Video Recorder

Brand: IC Realtime Pages: 118

Mobile Network Video Recorder

Brand: IC Realtime Pages: 158

Brand: Billion Pages: 261

Brand: ProCurve Pages: 406

DGS-1510 Series

Brand: D-Link Pages: 711

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands