Cisco 901 Command Reference Manual Download Page 31

Page: 31 / 218

1-17

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

bfd all-interfaces

To enable Bidirectional Forwarding Detection (BFD) for all interfaces participating in the routing
process, use the

bfd all-interfaces

command in router configuration mode. To disable BFD for all

interfaces, use the

form of this command.

bfd all-interfaces

no bfd all-interfaces

Syntax Description

This command has no arguments or keywords.

Command Default

BFD is not enabled on the interfaces participating in the routing process.

Command Modes

Router configuration

Command History

Usage Guidelines

There are two methods to configure routing protocols to use BFD for failure detection. To enable BFD
for all neighbors of a routing protocol, enter the

bfd all-interfaces

command in router configuration

mode. If you do not want to enable BFD on all interfaces, enter the

bfd interface

command in router

configuration mode.

Examples

The following example shows BFD enabled for all Intermediate System-to-Intermediate System (IS-IS)
neighbors:

Router>

enable

Router#

configure terminal

Router(config)#

router isis tag1

Router(config-router)#

bfd all-interfaces

Router(config-router)#

end

The following example shows BFD enabled for all Open Shortest Path First (OSPF) neighbors:

Router>

enable

Router#

configure terminal

Router(config)#

router ospf 123

Router(config-router)#

bfd all-interfaces

Router(config-router)#

end

Related Commands

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Command

Description

bfd

Sets the baseline BFD session parameters on an interface.

bfd interface

Enables BFD on a per-interface basis for a BFD peer.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands