manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-113

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  rep platform fast-lsl enable

rep platform fast-lsl enable

To enable fast Link Status Layer (LSL) configuration on a Cisco ASR 901 Series Aggregate Services 
Router, use the 

rep platform fast-lsl enable 

command in global configuration mode. To disable fast LSL 

configuration, use the 

no

 form of this command. 

rep platform fast-lsl enable

no rep platform fast-lsl enable

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes 

Global configuration (config) #

Command History

Usage Guidelines

This command must be configured on the Cisco ASR 901 Routers to support Resilient Ethernet Protocol 
(REP) sessions with LSL timers that are less than one second long. When this command is configured, 
you can expect only subsecond convergence for REP. The subsecond convergence period is also 
applicable for normal REP sessions, if fast LSL is configured. 

Examples

The following example shows how to enable fast LSL configuration on a Cisco ASR 901 Router:

Router# 

configure terminal

Router(config)# 

rep platform fast-lsl enable

Release

Modification

15.3(3)3S

This command was introduced on the Cisco ASR 901 Series Aggregation 
Services Routers.

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Cambium Networks PTP 550 Series Quick Start Manual preview
PTP 550 Series
Brand: Cambium Networks Pages: 68
Cambium Networks PTP 820S Installation Manual preview
PTP 820S
Brand: Cambium Networks Pages: 110
Eaton Network Card-MS User Manual preview
Network Card-MS
Brand: Eaton Pages: 89
Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Brand: TE Connectivity Pages: 236
IBM TotalStorage SAN16M-R SAN Installation And Service Manual preview
TotalStorage SAN16M-R SAN
Brand: IBM Pages: 116
Paradyne 7995-A2-374 Quick Installation Instructions preview
7995-A2-374
Brand: Paradyne Pages: 1
Planet ADSL 2/2+ Router with USB Port ADE-3410v2 User Manual preview
ADSL 2/2+ Router with USB Port ADE-3410v2
Brand: Planet Pages: 62
Navini Networks RIPWAVE 40-00460-00R User Manual preview
RIPWAVE 40-00460-00R
Brand: Navini Networks Pages: 35
bintec elmeg RM7000 Installation Manual preview
RM7000
Brand: bintec elmeg Pages: 33
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Brand: Riverbed Pages: 38
Seriallink SLK-R602 Series Manual preview
SLK-R602 Series
Brand: Seriallink Pages: 29
XtendLan NVR-xUD User Manual preview
NVR-xUD
Brand: XtendLan Pages: 228
Mellanox Technologies ConnectX-3 Pro MCX349A-XCCN User Manual preview
ConnectX-3 Pro MCX349A-XCCN
Brand: Mellanox Technologies Pages: 35
Ubiquiti EdgeRouter PoE ERPoe-5 Quick Start Manual preview
EdgeRouter PoE ERPoe-5
Brand: Ubiquiti Pages: 13
Olicom Ethernet MCA 10/100 Adapter Manual To Operations preview
Ethernet MCA 10/100 Adapter
Brand: Olicom Pages: 88
Vacron VDH-NK300 Hardware Manual preview
VDH-NK300
Brand: Vacron Pages: 16
Broadband Products D-Link DSL-2640U Quick Installation Manual preview
D-Link DSL-2640U
Brand: Broadband Products Pages: 12

Brands by name

Popular brands

Load more brands