manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-109

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  qos-config scheduling-mode min-bw-guarantee

qos-config scheduling-mode min-bw-guarantee

To configure the Quality of Service (QoS) Scheduler, use the 

qos-config scheduling-mode 

min-bw-guarantee 

command in the interface configuration mode in which the queuing policy is 

configured. To remove this configuration, use the 

no

 form of this command. We recommend that you use 

the 

qos-config scheduling-mode min-bw-guarantee

 command for optical ports.

qos-config scheduling-mode min-bw-guarantee

no qos-config scheduling-mode min-bw-guarantee

Syntax Description

Command Default

None

Command Modes

Interface configuration (config-if) #

Command History

Usage Guidelines

This command allows the per-class rate to use unutilized bandwidth, if any, in addition to the minimum 
guaranteed bandwidth that is configured.

Examples

The following example shows how to use the 

qos-config scheduling-mode min-bw-guarantee

 

command:

Router # 

configure terminal

Router(config) # 

interface gigabitethernet0/8

Router(config-if) # 

qos-config scheduling-mode min-bw-guarantee

Related Commands

min-bw-guarantee

Assures minimum bandwidth guarantee.

Release

Modification

15.2(2)SNG

This command was introduced on the Cisco ASR 901 Routers.

Command

Description

interface gigabitethernet

Selects a particular Gigabit Ethernet interface for configuration.

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

YASKAWA SI-EP3/V Installation Manual preview
SI-EP3/V
Brand: YASKAWA Pages: 68
Netopia 3346-ENT Getting Started Manual preview
3346-ENT
Brand: Netopia Pages: 38
Matrix Switch Corporation MSC-5-3232 Product Manual preview
MSC-5-3232
Brand: Matrix Switch Corporation Pages: 61
Lancom 1821n Wireless Manual preview
1821n Wireless
Brand: Lancom Pages: 102
TP-Link TD-8816 Quick Installation Manual preview
TD-8816
Brand: TP-Link Pages: 2
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Brand: ANEP Pages: 48
Tripp Lite WEBCARDLX Owner'S Manual preview
WEBCARDLX
Brand: Tripp Lite Pages: 34
TRENDnet TW100-W2plus Specifications preview
TW100-W2plus
Brand: TRENDnet Pages: 2
TRENDnet TE100-S2424V Specifications preview
TE100-S2424V
Brand: TRENDnet Pages: 2
ADTRAN 1202052L1 User Manual preview
1202052L1
Brand: ADTRAN Pages: 136
ZyXEL Communications WAP6804 User Manual preview
WAP6804
Brand: ZyXEL Communications Pages: 114
Geneko GWR-A362 Quick Start Manual preview
GWR-A362
Brand: Geneko Pages: 8
Delta Electronics DVP Series PLC DVP04TC-H2 Instruction Manual preview
DVP Series PLC DVP04TC-H2
Brand: Delta Electronics Pages: 2
D-Link DIR-815 User Manual preview
DIR-815
Brand: D-Link Pages: 240
US Robotics 9107 Quick Installation Manual preview
9107
Brand: US Robotics Pages: 120

Brands by name

Popular brands

Load more brands